When the Power Fails: What Should Still Open on a Commercial Entrance
Automatic Door Opener InstallationMost building managers find out how their entrance behaves in a power failure during the power failure. The front doors stop swinging, a card reader goes dark, and somebody is standing in a lobby pulling on a handle that will not move. None of that is unusual, and almost all of it is predictable from the hardware that is already on the door.
This is a plain walkthrough of what happens to an automatic entrance when the power drops, which parts are supposed to keep working without electricity, and what to check before the next outage rather than during it.
Electricity does one job on a door, and it is not holding the door shut
On a well built entrance, the thing keeping the door latched is mechanical. The electric parts either release that latch for a credential, or they move the door panel. Power loss should therefore take away convenience and access control, not the ability to get out.
Where that goes wrong is when an electrified device has been chosen or wired in a way that locks the leaf rather than controls it. That is why the two terms below matter more than any brand name on the hardware.
Fail-safe and fail-secure are opposites, and both are correct somewhere
A fail-safe device unlocks when power is removed. A fail-secure device stays locked when power is removed. Neither is better in the abstract. A stair door into a tenant space is often fail-secure on purpose, because a blackout should not open the building up. A door on an egress path that depends on electric release is normally fail-safe, because people have to get out whether or not the panel is energised.
The failure people run into is a mismatch: a fail-secure strike on a door that has nothing else to let people through, or a magnetic lock on an exit with no mechanical override. Those are design problems, and no amount of maintenance fixes them.
Magnetic locks are the ones worth looking at first
A mag lock holds by electromagnet, so it releases when power is cut. That sounds reassuring until the holding force is still on because the door sits on a circuit that did not drop, or because the release device on the inside is broken and nobody noticed. Mag locks are normally tied to a request-to-exit sensor, a push button, or door-mounted hardware. Every one of those is a part that can fail quietly, because the door still works perfectly on a normal day.
What should still open with the power off
Mechanical exit hardware. A panic bar or exit device is a spring and a latch; pushing it retracts the bolt whether or not the building has power. The same is true of a lever on a standard lockset and a thumbturn on a deadbolt.
Swing doors with an automatic operator are the ones that surprise people. Most operators can be pushed by hand when they are not energised, because the motor disengages or freewheels. The door becomes heavy rather than locked. That is normal, and it is also why the closing speed and force on those doors needs checking: an operator that has been adjusted to compensate for a dragging panel will be far heavier than it should be once the power is gone.
What usually does not keep working is anything on the credential side. Readers, keypads, intercoms and electric strikes sit idle. If the only way through a particular door was a fob, that door is closed for the duration.
The parts of the chain that break in an outage
Battery backup that was never tested
Plenty of operators and access panels have a backup battery. Batteries age whether or not they are used, and a unit that reports a fault only on its own small display will sit there for years with nobody reading it. The time to find that out is a scheduled test, not an emergency.
Door position switches and sensors
Safety sensors on an automatic door are part of why it is allowed to operate at all. After a power cut the operator reinitialises, and a sensor that was already marginal can come back out of calibration — which shows up as a door that stalls, reverses, or refuses to cycle. That is a automatic door repair call, not a reset that can be clicked away.
Accessible operators and push plates
Accessible entrances take the outage hardest, because for some users the operator is the only practical way through. A heavy manual swing is a locked door in effect. Buildings that treat this seriously keep the operator on a circuit that is covered, and they test the actuators on a schedule. If an entrance is being upgraded, the time to resolve the power question is during accessible door operator installation, while the wiring is still open.
Re-latching after the power returns
The quiet failure is the one after the outage, not during it. Doors that were propped or held open through the event often do not re-latch cleanly when everything energises again, especially where a closer is out of adjustment. A building can sit with an unlatched exterior door for days because nobody walked the perimeter afterwards.
What to check before the next one
Walk the building with the power on and ask a short list of questions at every opening that has anything electric on it. Can a person on the inside get out using only mechanical hardware? Is there a release device, and does it actually work when pressed? Does the door latch on its own from a quarter open? Is there a backup battery, and when was it last proved rather than assumed?
Write the answers down per door. That document is what turns a guess into a job list, and it is the backbone of any commercial door maintenance program that is worth paying for. A walkthrough also tends to surface things nobody reported: a dead push plate, a sensor taped over, a strike that has been jammed with a shim since the summer.
Frequently asked questions
Will my automatic doors open during a power outage?
They will usually stop operating and become manual. Most operators can then be pushed open by hand, though the door will feel heavy. Whether they can be pushed depends on the operator and its condition, which is why it is worth testing rather than assuming.
Is a magnetic lock legal on an exit door?
Mag locks are used on exits in Ontario, but only as part of an arrangement that releases them reliably, and the requirements depend on the building, its occupancy and the authority having jurisdiction. If nobody can tell you how a particular mag lock releases, treat that as the finding.
Why did my card reader stop working after the power came back?
Access panels reboot, and a controller with a failed backup battery can lose its state or come up in a default mode. Readers also share circuits with other equipment, so a breaker that tripped during the event can leave one door dark while the rest of the system looks fine.
Do panic bars need power?
A standard panic bar is purely mechanical. Some are electrified for alarms, monitoring or remote release, and those added functions stop in an outage — but pushing the bar still retracts the latch.
How often should a building test this?
Tie it to whatever inspection cycle the building already runs, and include a manual-egress check at every electrified opening. The test is quick; the value is in doing it on a schedule so a dead release device cannot sit unnoticed for a year.
