Clear Opening, Not Door Width: What Gets Missed When a Commercial Door Is Replaced
commercial Door RepairSomeone measures the old door, orders the same size, and the new one goes in. A month later a delivery cart will not fit through an opening that used to take it, or an inspector flags a doorway that has been there for twenty years. Nothing was ordered wrong. The door is the size it always was. What changed is the clear opening, and that is a different number from the door width.
Door width and clear width are not the same measurement
The width written on a door is the width of the slab. The number that matters in use is how much unobstructed space is left for a person or a load to pass through when the door is open. Several things sit between those two figures.
The door leaf itself
A swing door at ninety degrees does not get fully out of the way. Its thickness, plus however far the hinge arrangement holds it off the frame, stays in the opening. On a standard butt-hinged door that is a modest loss, but it is a loss, and it is the baseline that everything else is subtracted from.
Stops and the frame
The frame rebate and the door stop reduce the opening on both sides before the door is even considered. Frames are not all equal here: a heavy pressed steel frame takes more of the rough opening than a slim aluminium one, which is one reason a like-for-like replacement into a different frame type changes the result.
Hardware on the face of the door
This is where the surprises live. Surface-mounted hardware projects into the opening and travels with the door.
- A surface-applied exit device sits proud of the door face and swings through with it.
- Pull handles and panic bar end cases project further than people expect.
- A surface closer arm, and its bracket, occupy space at the head.
- Kick plates and armour plates add thickness, modestly but really.
Replace a door that had a mortise lock with one carrying a surface-mounted exit device and the slab width has not changed by a millimetre while the usable opening has shrunk noticeably.
How far the door can actually swing
A door hard against a return wall, a radiator, a column or another door cannot reach ninety degrees. Whatever angle it stops at is the angle that defines your clear width, and nobody discovers this until the door is hung.
Why this bites hardest on replacements
New construction gets this right more often, because the opening is designed around a required clear width and the hardware is specified alongside it. Replacements go wrong because the measurement taken is the one that is easy to take.
Three patterns account for most of it:
- Hardware changed with the door. Different lock function, different closer, a device added for code or security reasons, and the opening quietly narrows.
- Frame changed with the door. A new frame type with a deeper rebate in the same rough opening leaves less behind.
- Hinges changed. Swapping butt hinges for a continuous geared hinge, or moving to an offset arrangement, changes how far the leaf clears the frame, in either direction.
None of these are mistakes in themselves. They become problems when nobody checks what they do to the opening before the order goes in. Anyone quoting a door installation should be measuring the opening and specifying hardware as one exercise, not two.
Where the requirements come from
Minimum clear widths for doorways on an accessible route are set by building regulations and accessibility legislation, and the specific figures, which doors they apply to, and when an existing door has to be brought up to current standards all depend on your jurisdiction, the building type and what work is being done. In Ontario that means the building code and accessibility requirements both bear on it, and the answer for a renovation is often different from the answer for new construction.
Because of that, the only safe approach is to confirm the applicable figures with your local authority having jurisdiction or a designer before ordering, rather than relying on a number someone remembers. What is worth internalising is the principle: the requirement is written against clear width, not door size, so a door that satisfies it on paper can fail it once hardware is fitted.
Manoeuvring space counts too
Clear width through the opening is only part of it. There also has to be usable space on each side for someone to approach the door, operate it and get through, and that space depends on which way the door swings and which side the latch is on. A door in a tight lobby or at the end of a corridor can meet the width requirement and still be unusable for someone in a wheelchair because there is nowhere to position themselves to pull it.
Measuring it properly
The measurement to take is between the face of the open door, including anything mounted on it, and the opposite stop, with the door opened as far as it physically goes in that location. Not the frame to frame distance, and not the slab width from the order.
A short checklist before any commercial door is ordered:
- Measure the existing clear opening as it stands, with the door open as far as it goes.
- List the hardware going on the new door and how much of it projects from the face.
- Confirm the new frame’s rebate depth if the frame is changing.
- Confirm the hinge type, since it sets how far the leaf clears.
- Check what stops the swing: walls, columns, radiators, adjacent doors.
- Establish the required clear width for that specific door with your authority having jurisdiction.
- Compare the two numbers before signing anything.
What to do when the opening is already too narrow
Options exist short of rebuilding the wall, and they are worth knowing because the obvious answer is the expensive one.
Swing-clear hinges move the leaf almost entirely out of the opening, recovering close to the full thickness of the door. Changing from surface-mounted to concealed hardware takes the projection off the door face. Reversing the swing can free up manoeuvring space even when it does nothing for width. Where a leaf and a half arrangement exists, making the inactive leaf openable gives a wide clear opening when it is needed. And on an entrance that struggles regardless, a powered operator addresses usability even where width is fixed.
On aluminium storefront assemblies the frame members themselves take a meaningful share of the rough opening, so recovering width sometimes means reworking the frame rather than the door. That is a different scope from hanging a new leaf, and it is worth getting assessed by someone who does aluminum door work regularly before deciding what is feasible.
Frequently asked questions
Does a 36-inch door give a 36-inch clear opening?
No. The door thickness, the frame stop and anything mounted on the door face all sit in the opening, so the usable width is always less than the slab width. How much less depends on the hardware and hinge arrangement.
If I replace a door with the same size, can the opening change?
Yes, and this is the common trap. Same slab width with different hardware, a different frame or different hinges produces a different clear opening.
Do I have to upgrade an existing narrow doorway?
That depends on the jurisdiction, the building type and the scope of work being done, and it is a question for your local authority having jurisdiction. Replacing a door often triggers different obligations than leaving it alone does.
Which hinges give the most clear width?
Swing-clear hinges are designed specifically to move the leaf out of the opening and recover most of the door’s thickness. They change the door’s appearance and how it sits, so they suit some openings better than others.
Is it cheaper to widen the opening or change the hardware?
Hardware and hinge changes are the lighter interventions and are worth exploring first, because widening a structural opening brings in framing, finishes and often a permit. Which route is appropriate depends on how much width you need to recover, and that comes back to measuring the existing opening accurately. A contractor doing commercial door repair can usually tell you quickly which category your door falls into.
